From map to STL: how a city becomes a 3D print

A city model starts as a map and ends as a closed solid in millimetres. This guide explains each step in between: outlines, heights, terrain, water, and the checks that make the file printable.

Where the outlines come from

Building footprints come from OpenStreetMap and Overture Maps. These are open maps built from surveys, aerial imagery and volunteer mapping. Each building is a polygon: a closed line that follows its walls as seen from above. Roads, rivers, parks and bridges are stored the same way, as lines and areas.

These sources vary by place. Some towns are mapped very precisely, others only roughly. The tool uses what is there, so a missing or merged building on the map will also be missing or merged in the model.

How heights are added

A footprint alone is flat. To make it a building, the tool extrudes it straight up, so the walls are true vertical planes. How high they go depends on the data available for that place.

In regions with a national airborne laser survey, roof heights are measured. Elsewhere, heights are estimated from OpenStreetMap tags such as building height and number of floors, and the tool labels the model as estimated. Some landmarks use volunteer-made 3D models from OpenStreetMap.

  • Measured heights: France, Norway, the Netherlands, England, North Rhine-Westphalia and Flanders.
  • Estimated heights: the rest of the world, from building height and floor tags.
  • The label is shown in the tool, so you always know which you have.

Terrain, water, parks and bridges

The ground is a height surface under the buildings, so a hilly city has real slopes. Water is cut below its banks, so rivers and canals are channels rather than painted areas. Bridges are flat decks across the channel.

Parks are raised slightly above the ground, with paths cut through them, so green areas read as textured plates. Trees are optional small tree models. Every one of these layers adds geometry, so turning layers off gives a simpler, lighter file.

Why the result is one closed solid

A printer needs a model with a clear inside and outside. If a mesh has holes or loose faces, slicers guess, and prints fail or look wrong. The tool builds the city as one closed solid, so every surface joins another and there are no gaps.

Buildings, terrain, water cuts and the base are merged into that single shape. This is why you do not need a repair step in most slicers, and why the model is a solid block with detail on top rather than a pile of separate pieces.

What the STL units mean

STL files store coordinates as plain numbers with no unit. Slicers must assume one, and most assume millimetres. The tool writes the file in millimetres, scaled so the longest side matches your chosen print size, 180 mm by default.

That means a size you see in the slicer is a real print size. If the model looks tiny or huge on import, check that your slicer reads the file as millimetres rather than inches or metres. Scale in the slicer only if you want a different print size.

What the model cannot show

The model is a height-style solid. Each building has vertical walls and a roof level, with no see-through details. A lattice tower, such as the Eiffel Tower, becomes a stepped solid silhouette. Windows, facades and textures are not part of the data.

This is a limit of the data and of printing at city scale, where a metre is less than a quarter of a millimetre on the print. The model is best for form, layout and skyline: how a place sits together, not how each wall looks.

Try it on a real place

The studio is free and needs no account.

Questions

What format is the downloaded file?
A single binary STL file in millimetres. It describes the whole model as one closed solid with a base. Any slicer can read it, including Cura, PrusaSlicer and Bambu Studio, and in most cases it needs no repair before printing.
Why do some buildings look blocky?
Buildings are mapped outlines extruded straight up, so they have vertical walls and flat or stepped roofs. Complex roofs and facades are not in the data. Where a volunteer 3D model exists for a landmark, the tool may use it for a closer shape.

More guides: How to 3D print a city: a step-by-step guide · LiDAR to 3D print: using laser-survey data · Best print settings for 3D-printed city models