Best print settings for 3D-printed city models
City models are large, flat and full of small features. These starting points cover nozzle, layers, scale, infill, bed adhesion and material. They are generally accepted FDM defaults, not guarantees, so adjust for your printer.
Nozzle and layer height
A 0.4 mm nozzle is the usual choice and works well for city models. Layer heights between 0.12 and 0.2 mm are a common starting point. Finer layers show roof levels and edges more cleanly but add print time, while 0.2 mm is faster and acceptable for large buildings.
A smaller nozzle, such as 0.25 mm, can capture narrower walls and lanes, but it prints slowly and clogs more easily. Treat these values as starting points and run a short test if you are unsure.
Scale versus detail
Scale decides what survives. An 800 m frame at 180 mm is about 1:4,400, so 1 mm on the print is about 4.4 m on the ground. A 0.4 mm line is then about 1.8 m wide, which means a narrow lane or a thin spire may be too fine to print cleanly.
As a rough guide at that scale, a house of 10 m is about 2 mm wide, and a street of 12 m is about 3 mm. Alleys of 3 to 4 m close up. Print larger, up to 300 mm, or draw a smaller frame to keep small features open.
- Smaller frames give more detail at the same print size.
- Larger prints keep lanes open but need a bigger bed.
- Slim towers are the first features to fail at small sizes.
Walls, top layers and infill
City models are mostly solid blocks, so infill only matters inside large buildings and the base. A low infill such as 10 to 20 percent is a common starting point, and it saves time. Use two or three perimeters so that thin walls and towers have some strength.
Top layers matter on wide flat roofs and parks. Four or more top layers help hide infill patterns on large flat areas. If your slicer shows gaps in thin towers, add a perimeter or raise the print size.
Base thickness and bed adhesion
The default base is 2 mm thick. That is enough for most prints, but a thicker base makes the model stiffer and easier to handle. A large flat base is also the part most likely to warp or lift at the corners, because the whole plate cools at once.
Level the bed carefully and clean it. A brim of several millimetres helps hold the corners, and a slightly warmer bed can help. Keep drafts away from the printer. Warping is more common with materials that shrink as they cool.
Choosing a material
PLA is the usual choice for city models. It is easy to print, shrinks little, and holds crisp edges. White or light grey filament makes the shape easy to read, because shadows show the building forms. PETG is tougher but strings more, which can blur small details.
Materials that shrink more, such as ABS, tend to warp on large flat plates and usually need an enclosure. If you are new to printing, start with PLA, print a small frame first, and move to larger ones once the settings work.
Orientation, supports and slow areas
Print the model with its flat base on the bed. Walls are vertical, and the model is a solid, so supports are not needed in almost all cases. Check your slicer preview for any overhang you do not expect, particularly on landmarks that use volunteer 3D models.
Slim towers have little area per layer, so each layer cools slowly. A cooling fan and a lower speed near the top help. Some slicers can slow small layers automatically, which is worth turning on for tall, thin buildings.
Questions
- What layer height should I use for a city model?
- A common starting point is 0.12 to 0.2 mm with a 0.4 mm nozzle. Use 0.2 mm for speed and larger buildings, and 0.12 to 0.16 mm when roof levels and edges matter. Run a small test frame first, as results vary by printer.
- Why do the corners of my city model lift?
- The base is a large flat plate, and plates warp at the corners as they cool. Clean and level the bed, use a brim, avoid drafts, and try PLA, which shrinks less. A slightly warmer bed can also help hold the corners down.
- Can I print a city model without supports?
- In almost all cases, yes. The walls are vertical and the model sits on a flat base. Check your slicer preview for unexpected overhangs, and treat any setting here as a starting point rather than a guarantee.
More guides: How to 3D print a city: a step-by-step guide · From map to STL: how a city becomes a 3D print · LiDAR to 3D print: using laser-survey data