How to 3D print a city: a step-by-step guide
This guide takes you from a search box to a finished city model on your printer. You pick a place, draw a frame, choose layers, check a 3D preview and download one STL file ready for your slicer.
Pick a place and draw the frame
Open the studio and search for a city, a street or a landmark. The map jumps to it. Draw a frame over the area you want: a square or a rectangle, from 100 m up to 4 km on a side. You can rotate the frame, which helps when a river or a street grid runs at an angle.
Size matters more than anything else you choose. A frame of 500 to 900 m gives a model where single buildings stay readable. Very large frames fit a whole district, but each building becomes a small bump, so decide what you want people to recognise.
- Frames of 500 to 900 m suit one landmark with its surroundings.
- Frames of 1 to 2 km suit a district or an old town.
- Rotate the frame so a river or main street runs along one edge.
Choose the layers
The tool offers buildings, terrain, water, parks and trees. Buildings and terrain are the core of the model. Water is cut below its banks, so rivers and canals become real channels. Parks are raised slightly with paths cut through them. Trees are optional small tree models.
Each layer changes the print. Terrain suits hilly places and gives flat cities a gentle base. Trees add many tiny parts, so leave them off if you want a clean architectural look or if your printer struggles with fine detail.
Check the 3D preview
Before you download, the studio shows the model in 3D. Turn it around and look at the tallest buildings, the water and the edges of the frame. If a landmark is cut off, move or resize the frame and preview again. Nothing is committed until you download.
The preview also tells you whether the heights are measured or estimated. In regions with a national laser survey, such as France, Norway, the Netherlands, England, North Rhine-Westphalia and Flanders, heights are measured. Elsewhere they are estimated from map tags and labelled as such.
Set the print size and download the STL
Choose the longest side of the print. The default is 180 mm, and you can set anything from 60 to 300 mm. The base is 2 mm thick by default. Height exaggeration, from 1 to 3 times, stretches buildings and terrain vertically, which helps flat cities such as Amsterdam or Bordeaux.
Press download. You get one STL file in millimetres, built as a single closed solid. It needs no repair step in most slicers. A typical 800 m frame printed at 180 mm has a scale of about 1:4,400.
Slice the model
Import the STL into your slicer and keep the size as it is, since the file is already in millimetres. Place the flat base on the bed. The walls are vertical and the model is a solid, so supports are not needed in almost all cases. Check the preview layer by layer for thin towers.
A 0.4 mm nozzle with layers of 0.12 to 0.2 mm is a common starting point. Finer layers show roof levels more clearly but take longer. Large models can run for many hours, so plan the print around a day you can check on it.
Print and finish
Watch the first layers. The base of a city model is a large flat plate, which needs good bed adhesion and a level bed. Once the base is down, the rest of the print is mostly straightforward. Slim towers are the most likely failure, so slow down if your slicer lets you.
After printing, remove the model gently and trim any stringing. A light coat of matte primer makes a white or grey model look like an architectural massing model. You can paint rivers and parks by hand if you want colour.
Questions
- How long does a printed city model take?
- It depends on size, layer height and your printer. A model at 180 mm with 0.2 mm layers often takes many hours, and finer layers take longer. Your slicer shows an estimate before you start, so check it and adjust layer height if needed.
- Do I need supports to print a city model?
- In almost all cases, no. Buildings are extruded straight up, so walls are vertical, and the model sits on a flat base. Always check your slicer preview, especially for thin towers and any overhanging landmark shape.
- Is the tool really free?
- Yes. CitySlicer is free and needs no account. You search a place, draw a frame, choose layers, preview the model in 3D and download one STL file. The file is yours to print.
More guides: From map to STL: how a city becomes a 3D print · LiDAR to 3D print: using laser-survey data · Best print settings for 3D-printed city models